Fluke

Fluke 4265A Binary Programmable Power Source
Fluke 4265A Binary Programmable Power Source
Fluke 4265A Binary Programmable Power Source

Fluke 4265A Binary Programmable Power Source

USD $30

The Model 4265A is a programmable, bipolar dc voltage source.  Output voltage is from 0 to 65.532 vdc in two ranges; 16 and 65 vdc.  Programming resolution using the internal reference voltage is 1 mv on the 16 volt range and 4 mv on the 65 volt range.  Output accuracy is ±.01% of the programmed level on both voltage ranges.  After a 100 /sec settling time, a READY/NOT READY FLAG indicates that the output has settled to ±.01% of the programmed increment for a resistive load.  The output current is rated at ±1 ampere maximum and is limited to approximately ±1.1 ampere in the event of an overload or short circuit.

Stock: 1

Place order

FLUKE 867B Graphical Multimeter
FLUKE 867B Graphical Multimeter
FLUKE 867B Graphical Multimeter
FLUKE 867B Graphical Multimeter

FLUKE 867B Graphical Multimeter

USD $350

The Fluke 867B is the ultimate handheld tool for any application that demands real precision. Its 0.025% basic accuracy makes the tool an excellent choice for critical measurements. The Fluke 867B delivers the ultimate combination of functions and accuracy available in one handheld tool. Features Waveform Display to 1 MHz Safety-rated to 1000V Digital Display/Counts Selectable True-rms or Average Sensing Continuity/Conductance/Capacitance Duty Cycle/Pulse Width/Period/Frequency Min/Max/Average with Time Stamp Relative Mode Touch Hold and Peak Hold dB, AutoDiode Auto/Manual Ranging, Smoothing RS232 Interface (software and cable optional) Logic Activity Component Test LCD backlight Waveform memory Built-in NiCad charging Battery Eliminator.

This unit does not include the charger, software, and has not been thoroughly tested..  It includes the unit, and one set of probes.

Stock: 1

Place order

FLUKE 867 Graphical Multimeter
FLUKE 867 Graphical Multimeter
FLUKE 867 Graphical Multimeter
FLUKE 867 Graphical Multimeter

FLUKE 867 Graphical Multimeter

USD $200

Easy-to-use Waveform Display from dc to 1 MHz. Troubleshooting no longer means groping in the dark. Waveforms are like x-ray pictures of your electrical system. With automatic set-up you get the best view without fiddling with timebase, trigger levels, position, etc. A recorder that plots high resolution meter readings in intervals from 1 second to 15 minutes. Record your data in one of three modes-sample, high/low or average.  With the RS-232 interface, you can connect to your computer using FlukeView software and collect as much data as your hard disk can accommodate (software and cable optional).

Component Test for checking voltage-current signatures on resistors, capacitors, semiconductors and more.  Logic Test offers a simple way to indicate logic transitions to 10 MHz, showing if a circuit is active, stuck high, or stuck low. A Frequency Counter that measures up to 10 MHz.

This unit does not include probes, software, or charger.  Working condition is unknown.

Stock: 1

Place order

Fluke 100x Oscilloscope Probe
Fluke 100x Oscilloscope Probe

Fluke 100x Oscilloscope Probe

USD $10

Compatible with cat. III and IV standards of 1 000V and 60 V @ 10A.

Stock: 1

Place order

FLUKE 100X Oscilloscope Probe
FLUKE 100X Oscilloscope Probe

FLUKE 100X Oscilloscope Probe

USD $10

Compatible with cat. III and IV standards of 1 000V and 60 V @ 10A.

Stock: 1

Place order